One operatory Mobile Dental Van using 2018 Dodge Promaster Extended Cab Van per below specifications, cab & chassis specifications attached, modifications to van for dental application, and Drawing.
| Width: | Exterior | 82.7" |
|---|---|---|
| Interior | 76.7" | |
| Height: | Interior | 76.5" minimum |
| Exterior | 110" nominal | |
| Length: | Exterior | 250" |
| Exterior Color: | Bright White Clear Coat Exterior Paint |
|---|---|
| Interior Color: | Gray Interior Seat |
| Interior: | Cloth Buckets Seats |
| Engine: | 3.6 Liter V6 24- Valve VVT Engine |
| Transmission: | 6-Speed Automatic 62TE Transmission |
Note: Above specifications may vary due to van availability
The wall construction shall consist of the following:
The customer entry door shall be the side sliding door as provided by Dodge Promaster with accessory exterior running board step installed. The door will be insulated and covered with panel to match interior décor.
The sealed wood composite floor will allow no external moisture or mold buildup inside coach. Screw holes shall be sealed and sanded to smooth as required to prevent moisture from entering body and to provide a permanent smooth surface for installation of floor covering. The floor covering shall be easy clean wood grain vinyl.
Body shall be insulated with up to 3” thick closed cell foam insulation and fiberglass batt insulation with an R-factor of up to 20 for ceiling, sidewalls and doors to maintain the most comfortable working environment for tech and patient.
100” step slip resistant running board shall be installed at customer sliding entry door, and a 39” running board shall be installed at driver door for ease of entry and exit.
All interior white cabinetry shall be solid wood fronts with 5 ply plywood sides. All cabinet doors will include latches to prevent opening while in transit. Seven large two-door wall cabinets are included for accessory and supplies storage.
The ceiling shall be an easy clean vinyl covered plywood with (2) flush mounted high tech LED string lights, front to rear.
AC Electrical System: Shall be a 120VAC single phase system rated for anticipated load. System shall include a 60A/120vac rated distribution panel configured with UL listed type circuit breakers. Circuit breakers shall be sized per component manufacturers’ recommendation.
System shall be wired using 12 gauge, 3-conductor (12/3), 600V rated, UL approved, MC commercial cable. All wiring shall be color-coded: black = hot, white = neutral, and green = ground. Additionally, wiring shall be labeled listing circuit number and/or designation at all termination points. All wiring shall adhere to applicable NEC and FMVSS regulations.
Wiring shall be supported on 16” centers with insulated, non-conductive clamps. Wire bundles shall be tied with trimmed nylon ties. Extreme care shall be taken to prevent chafing, abrasion, and exposure to high heat. Wiring run in external areas shall be encased in liquid tight conduit to further protect against the elements and mechanical damage.
Specific number and type of receptacles shall be determined during the pre-construction process.
DC Electrical System: Shall be a 12VDC, negative ground system rated for anticipated conversion load. System shall include fuse panel using blade type fuses. All circuits shall be protected from over current by fuses rated for a minimum of 125% of anticipated load. 12VDC functions shall be clearly designated by printed labels. Wiring shall be labeled listing circuit number and/or designation at all termination points.
Generator battery system shall include one (1) deep-cycle gel cell sealed battery mounted inside van in a battery case. (1) 40AMP automatic battery maintainer to prevent battery overcharging.
System shall provide separate generator battery charging during operation periods when the vehicle engine is not running to prevent depletion of generator battery power.
All high-current battery cabling shall utilize full-length cable runs sized to load. Terminal ends shall be crimped with manufacturer recommended tooling and sealed using color-coded wrap.
All added wiring for 12VDC load runs shall be AWG 8, 10, 12, and 14, and conform to MIL-W-1678D type D. Wire terminals used shall conform to MIL-T-7928. Terminals shall be insulated with insulation grip, Type II, Class 2, and crimped with tooling recommended by manufacturer.
All added wiring shall be supported on 12” centers and bundles shall be tied with trimmed nylon ties. Entire system shall be installed to modern US automotive standards using best practices available at time of installation. Plastic/rubber grommets and/or dielectric sealants shall be used to protect wiring and/or looms where they pass through sheet metal, bulkheads, or structural supports. Convoluted polyethylene tubing shall be used to protect against chafing and abrasion where required. Extreme care shall be exercised to provide for easy serviceability of the system in future years. Extreme care shall be taken to avoid the engine manifold, engine exhaust, muffler, or any high-heat items that may subject the wiring to severe overheating during long periods of operation. These shall be the minimum acceptable wiring standards.
Install full length vinyl floor covering.
7.0 KW gasoline quiet Generator to be installed. Generator fuel line will be tied into the existing chassis fuel tank to allow 3” of fuel to remain. This is to assure the chassis fuel tank cannot be run out of fuel totally.
The generator shall be mounted beneath the vehicle under and through the left rear door with rear access. Generator installation shall be in full accordance with manufacturer’s recommendations including any air flow restrictions associated with the installation method. The generator exhaust pipe shall be routed to exhaust on roadside away from entry door.
A 1/8” thick steel sound-insulated compartment with proper supports, painted and undercoated as required, will be built to accommodate the required generator. The compartment will be securely tied into body framework to avoid damage to the compartment and the equipment by road vibration and road surface irregularities. Generator shall have one swing-up door with latch or ease of access, minimizing re-circulation preventing overheating and meeting all manufacturer’s requirements. The generator compartment shall be insulated using mechanical fasteners for elimination of heat, noise, and fumes to the coach area through walls and/or flooring without interfering with necessary airflow. Insulation of laminated sound deadening materials will surround all possible areas of the generator compartment. The latches will be Southco thumb-pull with adjustable twist lock security latches, keyed alike.
Generator start, stop switch and hour meter shall be located in the diagnostic suite cabinet for easy accessibility.
One (1) 13,500 BTU wall mounted central heating and air conditioning system with overhead delivery is provided. A 5200 btu floor heater with blower as well as (2) baseboard heaters are provided.
One (1) MCI PROPRIETARY heavy-duty commercial (4) point hydraulic stabilizing system with individual controls are provided and located at the passenger side rear door.
(2) lengths of 12VDC adjustable LED string lights shall be mounted flush with the ceiling, full length each side for a bright working space
As provided by Dodge
The doctor and assistant’s area will be constructed according to drawing #1000816 floor plan. The area will include the following:
Heavy-duty rubber covered 50’ long SO 10-2 with ground shoreline cord shall be provided. Generator/shorepower transfer switch is also provided.
(7) Interior wall storage cabinets will be provided according to floor plan drawing # 1000816
Wrap around windshield panel included
(Note: Substitution of dental equipment due to availability may affect price)
| OPTION | Mercedes Sprinter Diesel van in lieu of gasoline Promaster van: *Includes diesel generator FOB Amelia, Ohio Plus applicable Federal, State and Local taxes |
|
|---|---|---|
| TERMS | Down payment to include Promaster van purchase order Balance due upon completion, prior to shipment. Title to follow after payment in full. |
|
| MCI Warranty | One year parts and labor | |
| DELIVERY | Approximately 10 weeks after receipt of order and down payment contingent upon timely delivery of dental equipment and cab and chassis. | |
Up to 8 hours of training on coach system included at Amelia, Ohio, no driver training included.
Note: Imaging systems are sold Pre-owned, As-is, Where-is, with No Warranty Expressed or Implied. All Sales Final, No Returns, No exchanges. Request Pictures and Specs. E mail questions.
We sell, rent and export all types of mobile vehicles, including medical van, medical coaches, medical trailer, mobile dental clinics, mobile dental vans, new & used dental coaches, refurbished medical coaches & trailer and dental office in modified ocean type containers globally.
Join us to stay updated with our latest blog updates, news, tips, guide and annoucements!
3265 Summitrun Drive,
Independence, KY, 41051.
