sales@kbdentalconsulting.com      +1 586 917 0245

×
Quote Request
   Renting    Buying

left side

Commercial Mobile Dental Coach

SUMMARY FLOOR PLAN

  • 39’ long maximum x 102” wide x 13’ 5” tall nominal outside dimensions
  • Platform stair system
  • Reception area
  • Waiting area
  • (3) Dental Suites with (3) Expandable sides
Commercial Mobile Dental Coach

CAB AND CHASSIS SPECIFICATIONS (CDL REQUIRED)

Kenworth K3 Medium Duty Tilt Cab to include 260HP Engine and Allison

Automatic Transmission per Specifications below:

KENWORTH CAB & CHASSIS SPECIFICATIONS:

Model : K3 Series Medium Duty

Type : Full Truck

Fr Axle Load (lbs) 12,000
Rr Axle Load (lbs) 21,000
G.C.W. (lbs) 33,000
Tag Axle (lbs) 13,500
GVW 46,500
Wheelbase (in) 274
Overhang (in) 120
Cab to Axle (in) 263
Cab to EOF (in) 383

Model

  • K370 Class 7 Medium Duty COE
  • Medium-duty 4x2 automatic

Engine & Equipment

  • PACCAR PX-7 260 2017 260@2400
  • Includes turbo exhaust brake. Diagnostic Plug for data Link, Oil Cooler, Aluminum Flywheel Housing.
    • N09020 P02 - YES Cruise Control Auto Resume
    • N09040 P04 - NO Auto Engine Brake in Cruise
    • N09060 P06 - YES Gear Down Protection
    • N09100 P11 - NO Engine Protection Shutdown
    • N09120 P14 - 75 Max Vehicle Speed in Top Gear
    • N09140 P19 - 75 Max Cruise Control Speed
    • N09160 P26 - 1400 Max PTO Speed
    • N09180 P10 - YES Idle Shutdown
    • N09200 P32 - 5 Idle Shutdown Time
    • N09220 P33 - NO Idle Shutdown Override
  • Prospector version 39.1
  • Air compressor: Cummins 18.7 CFM FOR Cummins AND PACCAR PX engines.
  • Air cleaner – Fender Mtd RH BOC
  • Air Intake: High
  • Cooling Module
  • EXH:2017 EPA HORIZONTAL UNDER RAIL DPF/SCR FOR PX-7 WITH HORIZONTAL TAILPIPE BELOW RH RAIL, BACK OF CAB
  • Fuel Filter: PACCAR Standard Service Interval Fuel/Water Separator, 2017 Emissions
  • Run Aid: None (For Fuel Filter)
  • Start Aid: None (For Fuel Filter)
  • Immersion Type Pre-Heater 110-120V
  • Engine oil pan heater 120V 300W w/plug under door on C500, T660, T800 & W900
  • Alternator: Bosch 160 amp, brush type only
  • Batteries: 2 PACCAR GP31 threaded post (1000) 2000 CCA starting.
  • Starter: Delco 12V 29MT
  • Battery Disconnect Switch: 1 Battery box locking

Transmission & Clutch

  • Transmission: Allison 2500RDS 6-speed w/PTO drive gear. 5th Gen controls. Includes heat exchanger. Rugged Duty Series for vocational applications. Transynd transmission fluid is Standard on all Allison 1000, 2000, 3000 & 4000 series transmissions.
  • Driveline: 4 Dana SPL100; 3 center bearings light duty.
  • Torque converter included w/Allison Transmission.
  • Allison FuelSense Base: Includes EcoCal, 5th Gen Controls, and Dynamic Shift Sensing

Front Axle & Equipment

  • Dana Spicer E-1202IL Front Axle rated 12K 3 –1/2 in. drop. USE W/AIR BRAKES ONLY. MED DUTY ONLY.
  • Front brakes included w/front hub package.
  • 12,000 lb. Air brake package; drum brakes, iron 10-bolt hub piloted hubs.
  • 12,000 lb. Front spring suspension with shock absorbers
  • 12,000 lb. Capacity single power steering gear

Rear Axle & Equipment

  • Single Dana Spicer P22060S single reduction rear axle. T300/K300: use with/air brakes. Single rear axle 22K capacity rated at 21K.
  • Rear Axle Ratio – 5.29.
  • Single rear brakes included w/rear hub package.
  • 21,000 lb. Air Brake Pkg Included 16.5x7 in. brakes, cast drums, iron 10-Bolt hub pilot hubs, slack adjusters & oil seals for use with 22.5 wheels.
  • Spring brakes
  • Wabco Electronic Brake System (EBS) with anti-lock system. 4S/4M *FR WHL + 2 GRP RR WHL. K270/K370 only.
  • Wheel Differential Lock for Dana Spicer Axle P22060S; changes S to D to the axle part number.
  • Rear air ride suspension: single Hendrickson HAS23OL 23K. Welded steel cross member & gussets w/shocks at 8.3 in. laden height, 8.5 in. unladed height. Medium-duty. Included air suspension dump valve.
  • Tag Axle: Hendrickson Lift Axle ST Series Composite FX, 13,500 lbs with Air Ride Suspension and 14,000 lb air brake package

Tires & Wheels

  • Front tires: Bridgestone R268ECOPIA 11R22.5 14PR. or equivalent 41.5 in. diameter, all position. F-side wall protector bar. 19.3 in. SLR. For P & D & construction vocations. Smartway certified. Code is priced per pair of tires.
  • Rear Tire Quantity: 4
  • Tag Axle Quantity: 2
  • Front wheel: Alcoa 88367 22.5x8.25 aluminum with Lvl OneTM finish, hub pilot mount. 7,400 lb. maximum rating. Air disc brake compatible.
  • Rear wheel: Alcoa 88367 22.5x8.25 aluminum with Lvl OneTM finish, hub pilot mount. 7400 lb. maximum rating.
  • Rear Wheel/Rim Quantity: 4
  • Tag Axle Wheel: Alcoa 88367, 225 x 8.25 aluminum with Lvl OneTM finish, hub pilot mount, 7400 lb maximum rating.

Frame & Equipment

  • Frame Rail: 1-1/4 in. steel to 414 in.
  • 240 inch wheelbase plus 55” to tag axle
  • Bumper: Steel painted gray.
  • Steel space saver battery box, right hand back of cab. With aluminum cover.
  • Battery box location: RH Side.
  • Square End-of-Frame without cross member.

Fuel Tanks & Equipment

  • Fuel Tank: 45 US gallon rectangular steel left side plus 45 gallons right side
  • Rectangular DEF tank. 15 gallons of useable volume. The tank will be located just forward of the under cab component on the side you specified. Standard capacity is calculated by fuel capacity of the vehicle and will accommodate two diesel fill-ups for every DEF fill-up. For 1:1 DEF fuel fill ratio, add 7889204.
  • DEF tank location is on the LH.
  • Location: 45 gal fuel tank LH behind cab and RH behind cab

Cab & Equipment

  • Steel Cab: BBC 63.4 in Non-Slpr LHD with WABCO EBS Steel 63.4 in. BC, CE, Left Hand Drive, with the following; Day cab rear window with tinted safety glass throughout, Electric windshield wipers with intermittent feature, Electric-Powered LH & RH window lifts with switch located on door pad, Heated driving mirrors LH & RH with convex mirror over RH door, High level gray interior trim, Rubber floor mats, Combo fresh air heater and air conditioner, Smartwheel – 18 in. black four spoke soft touch steering wheel with adjustable tilt steering column, Electric horn, 12V cigar lighter with ash tray, Driver and Passenger seats, Console mounted push button transmission controls and back wall storage. Includes WABCO EBS.
  • Heater and Air Conditioner
  • Switch & Wiring for Customer-Installed PTO Electric over hydraulic PTO. Includes switch guard. Wiring is routed to LH frame for connection to the customer installed PTO. No air controls are provided with this code.
  • Dual Scale Speedometer MPH Over KPH. Includes: Speedometer with clock and outside air temperature displays
  • Water Temperature Gauge, Fuel Level Gauge, Dual Air Pressure Gauges, DEF Level Gauge and Visual & Audible System Warnings
  • Interior: Gray
  • Drivers Seat: Sears C2 Air, High Back Fabric
  • RD Seat: Sears C2 Air, HB Fabric
  • AM/FM/CD/Bluetooth Radio, Speakers, Wiring and Antenna
  • Center Console with Storage and 2 Cup Holders
  • Dual Heated and Motorized Mirrors, Includes 2 convex mirrors and 1 downward looking mirror on passenger side.

Lights & Instruments

  • Headlamps: Halogen Projector Low Beam, Halogen Complex Reflector High Beam
  • Turn Signal
  • External Lights – Fog / Driving Lights
  • Combination Stop, Tail, Turn & Backup Lights RH & LH
  • Daytime Running Lamps.
  • Electric Backup Alarm: Meets SAE J994 & OSHA requirements.
  • Body Builder Harness Coiled End of Frame 34 ft.

Air Equipment

  • Air Dryer: WABCO SS1200 Plus without Multi Port PPV
  • Extended Warranty : Medium–duty Warranty - 1-year/ unlimited mi.

Paint

  • Paint color number.
  • K270/K370 Paint Color M8870 Ice White
  • Color Paint – Day Cab Color will be White if no other color is specified.

COMMERCIAL SPECIFICATIONS

BODY CONSTRUCTION:

Floor:

  • 80,000 psi Hi-strength primed and painted trailer I-beams on 16 inch centers
  • I-beams bolted to custom POWDERCOATED aluminum extruded side lower body rails with 5/16" torq button head plated steel bolts with self-locking nuts covered with a vinyl insert.
  • 8” steel 3/16 THICK continuous primed and painted channel welded to underside of 4” steel I-Beams.The steel channel shall have reinforcing gussets welded into place on 4’ centers.
  • Sub floor shall be continuous one-piece 1/2” gelcoated FRP, BOTH SIDES with sealed edges to prevent mold and moisture intrusion; installed with ¼” plated steel flathead floor screws on 16” centers.

COMPARTMENTS:

  • All storage compartments shall be 1/8” aluminum
  • All compartment doors shall be 1/8” aluminum using an aluminum continuous hinge and sealed shelter-lite covers over hinges riveted to compartment. Doors shall have recessed bulb compression seals all around edges for unique no leak sealing feature.
  • Southco thumb pull with adjustable special twist-lock security key shall be installed on each door. All storage door keys keyed alike.

SKIRTING:

All skirting shall be 1/8” aluminum with 3/16” white chip/salt resistant white gel coated fiberglass wheel wells and shall be riveted in place using 3/16” aluminum rivets on 6” centers. All interfaces to be sealed with white non-yellowing Manus sealant.

EXTERIOR ROOF / INTERIOR CEILING and EXTERIOR SIDEWALLS / INTERIOR WALLS:

  • Exterior surface shall be white fiberglass gel-coat .014-.018 thick.
  • Vacuum bonded to ¼” thickness exterior continuous plywood.
  • Vacuum bonded to a 2” insulated foam core
  • Vacuum bonded to 1/4” interior continuous plywood sheet.
  • Interior wall surface is.014-.018 gel-coat
  • Commercial vinyl wall paper for the interior walls from selection. The total thickness of wall shall equal 2.65 inches minimum.
  • Additional insulated 1” ceiling no flake ceiling panels shall be installed into white grid dropped ceiling.

NOTES:

  • High strength aluminum 2” square tube with .090” wall thickness minimum perimeter frame on 26” centers shall be vacuum bonded into all wall structures and door frame openings creating the strongest wall structure in the industry.
  • All corner junctions shall have a .125 minimum wall thickness custom primed and painted aluminum corner and custom aluminum upper body rail.
  • R-factor (Insulation factor) shall equal 14 for ceiling and side walls, R-factor shall equal R-14 for floor
  • 3” radius aluminum extruded corner cap riveted and sealed on all 4 corners with Manus sealant.
  • All mill finish aluminum shall be epoxy primed and painted (2) coats commercial urethane white.

MISCELLANEOUS:

  • BUMPER: ICC H.D. 5” Channel full width
  • All painting shall be done in a specially designed, negative pressure, temperature-controlled, enclosed paint booth. The entire body shall be thoroughly cleaned, sanded, primed with urethane-based primer as required, and painted with two (2) coats of commercial, high grade polyurethane paint
  • Body undercoated with a heavy-duty water sealant and sound-deadening material for protection against rust and stone damage
  • WINDOWS: Per drawing shall be darkened safety glass with insect screens and Venetian blinds. Sealed to properly protect from weather and dust.
  • Floodlight above entrance/exit door.
  • LED exterior light system as required by DOT (reverse, turn signals, stop, running, emergency)

SYSTEMS:

ELECTRICAL:

  • 12 Volt DC and 220 Volt/60Hz Alternating Current system
  • 100 amp, single phase 220VAC/60 Hz Distribution panel and circuit breakers, number and size dictated by National Electric Code (N.E.C.)
  • New 22.5kw Diesel generator w/100 AMP/220v single phase/60 Hz circuit breaker, on/off switch, LED diagnosis board, mounted on slides
  • Generator remote start panel with oil pressure, water temp, frequency, voltage, and amp meter
  • Electrical manual transfer switch from shore power to generator
  • 220v/60 Hz, SO wire 45’ single phase cord per NEC
  • Power panel and breakers with (4) wire/SO cable with weather proof plug, GFI circuit breakers as required. All wiring per NEC. Mating shore power plug included.
  • 220v/60 Hz VAC Lighting: Commercial 2 tube and 4 tube troffer fluorescent lights as required
  • 12VDC Lighting: Emergency interior lighting (2), exterior lighting (1), Storage compartments (2), (electrical and generator)
  • Extra heavy duty hydraulic leveling system with (4) lever control

HEATING, VENTILATION, AND AIR CONDITIONING:

  • (1) New 42,000 BTU rear mount central air conditioner for environmental control. 10,000 watt built-in heat strip.

COMPUTER / COMMUNICATIONS:

  • Pre-wire for telephone as required. Jack location to be determined at design review.
  • Pre-wire for CAT5 computer ports as required per design review
  • Telecommunication equipment by others.

INTERIOR DECOR:

  • Interior walls shall be covered with commercial easy clean vinyl wall coverings
  • Floor covering: Finish floor shall be skid resistant and of fire retardant commercial vinyl floor covering.
  • Overhead base and wall cabinets shall be customer choice of wood construction with Corian or equivalent one piece formed countertops, easy clean work surfaces. Cabinetry to include positive latches to secure cabinet doors during transit.
  • Electrical outlets, switches, and cover color: White
  • Interior doors and trim shall be painted (2) coats semi-gloss latex.

PAINT:

  • Mill finished exterior aluminum extrusions shall be epoxy primed and painted two coats of high solids commercial urethane paint.
  • Interior metal surfaces are primed and painted two coats of semi-gloss latex enamel.

MISCELLANEOUS:

  • Stair System: Powered platform stair system
  • Entry/Exit Door: 32” wide commercial insulated door with aluminum frame, tempered glass and commercial lever lock. Threshold with no leak / no bind door seal mounted in custom frame
  • Back-up alarm operable in reverse only
  • Total underbody is rust-proofed undercoating
  • Dropped ceiling mount fluorescent light fixtures included as required
  • One scene light included above door
  • All windows shall have day/night blinds installed
  • Data ports as required throughout coach as required
  • Dropped ceiling with additional insulating factor included
  • Minimum finished ceiling height: 89”
  • A full set of operating manuals are included
  • Acceptance shall be at factory by customer’s representative prior to shipment to port to facilitate any changes require*

CALL FOR PRICE

CAB, CHASSIS AND DENTAL BODY PER SPECIFICATIONS ABOVE:
CAB, CHASSIS AND DENTAL EQUIPMENT:
QTY UOM DESCRIPTION
3 EA Ritter Vanguard Operatory Dental Chair Package
1 EA Ritter oil less compressor with Dryer, #RA 7/2 D 2HP, 230 volts
1 EA Ultrasonic Cleaner 1.5 Gallon
1 EA Masterlink MaxRay Portable Handheld Dental X-Ray unit
1 EA Masterlink Apex Digital Sensor standard package
1 EA #400616 Sterident 1.5 HP Vacuum Pump brushless motor
1 EA Midmark M9 Automatic Ultra Clave Autoclave
Option 18’ Manual Awning
Terms

40% Down

40% Interim payment 6 weeks into Production cycle

20% Final payment

Wire Transfer required
Delivery 12-16 weeks, contingent upon timely delivery of truck cab and chassis, dental equipment, and current production schedule.
Training Up to 8 hours training included at MCI facility in Amelia, OH.
Warranty
Cab & Chasis Per Kenworth Warranty
Body & Chasis 12 months parts and labor

Note: Imaging systems are sold Pre-owned, As-is, Where-is, with No Warranty Expressed or Implied. All Sales Final, No Returns, No exchanges. Request Pictures and Specs. E mail questions.

Subscribe to Our Newsletter!

Join us to stay updated with our latest blog updates, news, tips, guide and annoucements!

Copyright © KB Consulting, LLC- All Rights Reserved

Terms & Conditions | Website Development, Maintenance Services and SEO Services by Skynet Technologies | Sitemap